55 mm x 120 mm x 43 mm FAG 22311-E1-T41A Bearing

d2 max.:137 mm; α:6 °; Specific dynamic load factor K:100 N/mm²; B:44 mm; h1:225 mm; d4 ≈:82 mm; w:70 mm; Material constant KM:330; C1 max.:39 mm; r1 min.:1 mm;

Tolerance shaft:e7; α:124 °; Specific static load factor K0:45 N/mm²; a:3 mm; h:56 mm; Permissible sliding velocity v min.:0 m/s; Permissible sliding velocity v max.:0.5 m/s; Coefficient of friction µ min.:0.08; Tolerance housing:H7; d:55 mm;

J min.:371.475 mm; PG:1/4 NPT; Cap bolt, SAE grade:8; Bearing:1322 KM; P90°:113 kN; P120°:73.8 kN; Appropriate attachment bolt size G:0.875 in; J max.:406.4 mm; Housing:SAF 622; Mass pillow block:62.8 kg;

Maximum static radial loads F0r max.:1180 kN; H max.:84.965 mm; F:159.375 mm; d:130 mm; C:172.64 mm; B:172.64 mm; E:218.46 mm; Basic static load rating C0:1800 kN; Basic dynamic load rating C:1170 kN; r min.:2.7 mm;

Accessories:Shield & Seal; Oil Speed Rating n2:12000 rpm; Fillet Radius ra:1.00 mm; Grease Speed Rating n1:8500 rpm; D:52.0000 mm; Basic Static Radial Load Rating Co:14600 N; Basic Dynamic Radial Load Rating C:22500 N; Sealed Speed Rating n3:8500 rpm; d:20.000 mm; B:22.20 mm;

Fillet Radius rb:1.00 mm; Fillet Radius ra:3.00 mm; Oil Speed Rating n2:1800 rpm; d:280.000 mm; Grease Speed Rating n1:1100 rpm; D:460.0000 mm; Basic Dynamic Radial Load Rating C:403000 N; B:63.00 mm; Basic Static Radial Load Rating Co:600000 N;

B:22 mm; F:50 mm; r, r1,2 min.:1 mm; Mass inner ring:0.12 kg; d:40 mm;

Grease Speed Rating n1:2000 rpm; B:1.5000 in; Fillet Radius ra:0.12 in; D:11.5000 in; Basic Static Radial Load Rating Co:232000 N; Oil Speed Rating n2:2800 rpm; Basic Dynamic Radial Load Rating C:163000 N; d:8.500 in; Fillet Radius rb:0.060 in;

Calculation factor e:0.3; Fatigue load limit Pu:440 kN; b:22.3 mm; Calculation factor Y2:3.4; da max.:361 mm; d3:400 mm; Basic static load rating C0:6100 kN; Da max.:520 mm; Limiting speed:260 r/min; K:12 mm;

Cap bolt recommended tightening torque:149.1 N·m; P90°:59.6 kN; H:161.925 mm; Labyrinth ring:2 x LOR 37; S:3.175 mm; ba:32.544 mm; A2:120.65 mm; P180°:40 kN; L:285.75 mm; Housing:SSAFS 515;

Initial grease fill:175.77 g; Stabilizing ring:SR-16-13; Taconite seal (dc shaft position):TER 54; S:4.763 mm; P90°:82.7 kN; A1:88.9 mm; Cap bolt, SAE grade:8; da:80 mm; Housing:SAFS 216; P150°:44.5 kN;

Specific static load factor K0:20 N/mm²; Tolerance housing:H7; Coefficient of friction µ min.:0.05; Permissible sliding velocity v max.:5 m/s; Coefficient of friction µ max.:0.1; B:70 mm; Permissible sliding velocity v min.:0.25 m/s; d:80 mm; Mass bushing:0.58 kg; D:90 mm;

Grease Speed Rating n1:2800 rpm; Basic Dynamic Radial Load Rating C:195000 N; D:150.0000 mm; Fillet Radius ra:2.00 mm; B:70.00 mm; d:60.000 mm; Basic Static Radial Load Rating Co:173000 N; Fillet Radius rb:1.00 mm; Oil Speed Rating n2:4000 rpm;

Accessories:Shield & Seal; D:95.0000 mm; B:18.00 mm; d:60.000 mm; Basic Static Radial Load Rating Co:25000 N; Oil Speed Rating Open/Shielded n2:8000 rpm; Basic Dynamic Radial Load Rating C:32500 N; Grease Speed Rating Open/Shielded n1:6700 rpm; Sealed Speed Rating n3:4300 rpm; Fillet Radius ra:1.00

D:70 mm; Permissible sliding velocity v min.:0.25 m/s; B:70 mm; Permissible sliding velocity v max.:5 m/s; Coefficient of friction µ min.:0.05; Specific dynamic load factor K:10 N/mm²; Coefficient of friction µ max.:0.1; Tolerance shaft:h8; d:50 mm; Specific static load factor K0:20